Duraflame Burner 61000 User Manual download pdf (Page 10)

-10-

3. Check each component for shipping damage. If components are damaged, contact the store

where purchased or Duraame, Inc.

4. Check the rebox dimensions to ensure that they are at least equal to the minimum dimensions

shown in Figure 2. The minimum clearances that the appliance originally required will be

adequate for this installation. You will need the two (2) ¼” x 1 ½” masonry screws provided for

this step. Place the burner / base in a solid-fuel-burning masonry replace, a UL127 factory-

built replace, or an approved (to ANSI Z21.92) ventless rebox, centered left to right on a level

surface. When it is positioned properly, mark the screw locations through the screw-down

holes in the back legs of the base (see Figure 1). If you are installing the appliance in a brick-

bottomed replace, mark the screw locations in a mortar joint between the bricks. Remove the

appliance, and drill holes at the marked locations using a 3/16” masonry drill bit. Replace the

appliance, and attach it to the replace oor using the masonry screws.

5. For this appliance to function properly, the burner / base must be stable and level. If the oor

of your replace is uneven or out of level, you must shim under the front grate legs or the rear

support of the burner / base. Shim only with metal washers or other non-ammable objects.

6. Place the back log on the shelf at the rear of the appliance (see Figure 4). Make sure it is

centered left to right and that it sits so that the front part of the log is behind the front edge of

the metal part it sits on. Next set the front log in place (see Figure 5). The cavity of the log ts

over the fuel canister tray. The metal plate faces the rear of the appliance, and the log rests on

the grate. Check to see that the log is centered by opening the fuel canister door and looking

into the fuel canister cavity. The canister tray should be centered in the opening with the gap

between the canister tray and the log wall on the left (Figure 6) is equal to the gap on the right

(Figure 7). Also, push the log as far back as possible. Then place the left and right small logs

on top of the front and rear logs (see Figure 8). Ensure that when the door on the front log is

opened and you look down the front edge, that the canister tray is touching the inside wall of

the front log and the back edge of the canister tray has a gap between it and the inside wall of

the front log (see Figure 9). Make sure that the screws protruding from the metal plate are not

resting on the back edge of the tray.

7. Make sure the charred area on left small log faces the inside of the log set. The pins are on

the small logs and the holes are in the front and rear logs. If the back log is too far back or too

far to the front, move it so that the pins t properly. This will ensure that the logs are placed

properly. NOTE: When the log pile is properly positioned, the ames should be centered in the

log pile and should not come into contact with any of the logs. If there is contact, extinguish

the appliance using the built in snuer device, allow the unit to cool for at least 30 minutes, and

reposition the log pile so that the ames are centered.

8. Next step is to install the battery into the igniter. The igniter is on the left side of the appliance

towards the front just under the front log (see Figure 1). The button and front cover of the

igniter twists o (see Figure 1). Twist the front o, install the battery and twist the front back on.

Push the button and you should hear the sparker creating the sparks. If you do not hear or see

the sparks, you either have a dead battery or you did not install the battery properly. If after

remedying both issues the sparker still does not create a spark, contact the installer, the store

where you purchased the product or Duraame, Inc.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 19 20

WARRANTY INFORMATION 19

Comments to this Manuals

No comments

Duraflame Burner 61000 User Manual Page 10

Comments to this Manuals